This product is for adult use only. You must be 21 or older.
RDAs · RTAs & RDTAs · Sub-ohm tanks · Coils, wire & cotton

Where the flavor happens

The atomizer is the part that actually makes the vapor — and it’s the part we obsess over. Drippers, tanks, rebuildables and everything to feed them, picked and built by people who chase flavor for a living.

Shop all atomizers How an atty works Find my atty
0Atty types
0RDAs, RTAs & tanks
0Free first build
Pick your atty

Four ways to build flavor

Anatomy of an atty

Tap a part. See what it does.

Every atomizer — dripper, tank or rebuildable — is the same seven ideas stacked up. Once you know them, specs stop being gibberish and you can tell in five seconds whether an atty is built for flavor, clouds or convenience.

Part 1 of 7

Drip tip

The mouthpiece. 510 tips are universal and swappable; 810s are wider for airier draws. Bore size changes the feel more than you’d think — narrow for MTL, wide for clouds.

In the case

The flavor wall

High-end and limited runs come and go fast — if you see one you want, call the store and we’ll hold it.

Build bench

Ohm’s law, no math

Building your own coil? Punch in the resistance and see what your battery is being asked to do. Regulated mods handle this for you; on a mech, you are the chip — so check before you fire.

  • Green — comfortably inside a quality 20A+ cell’s continuous rating.
  • Amber — only on a true high-drain cell (Molicel P28A/P42A, Samsung 25S/30T). Know your CDR.
  • Red — don’t. Rebuild higher or switch to a regulated mod.

Guide only. Always use authentic cells with intact wraps, a multimeter/ohm reader, and ask us if you’re unsure — checks are free.

16.8amps drawn
70.6watts at the coil
4.2volts

Shop atomizers

Ready to build?

Shop all atomizers →
Find my atty

Three questions. One atomizer.

Tell us how you vape and how much you want to build — we’ll point you at the right type, then you can shop it or come build one with us.

What’s it going on?

Will you build your own coils?

What do you care about most?

Our pick

Shop it →
Side by side

Tank vs. RTA vs. RDA

Sub-ohm tankRTA / RDTARDA
Flavor●●●○○●●●●○●●●●●
Juice capacity●●●●○●●●●○●○○○○ (●●●●○ squonked)
Ease of use●●●●●●●●○○●●○○○
Cost per coil$3–5¢¢
Leak riskLowLow–mediumLow (drip) / overfill (squonk)
Works on a mech?Not recommendedYes, with careYes — the classic pairing
Good first atty?YesAfter a tankWith a squonker or a lesson
The atomizer wallThe wall, Johnson City
Why buy attys here

Built, wicked, dialed in.

  • Free first build — buy any rebuildable and we’ll coil it, wick it and set your wattage before you leave. Then we show you how.
  • Authentic only — Psyclone, dotMod, CCI, Alliance Tech, Mission XV: from the maker or authorized distro. No clones.
  • Deepest RDA case in the Tri-Cities — high-end, limited and squonk-ready drippers you won’t find at the gas station.
  • Re-wicks and rescues — burnt taste, gurgle, leak? Bring it in. Five minutes, usually free.
  • Rewards on every purchase — points in store and online.
Shop atomizers See squonk gear →
FAQ

Atomizer questions

RDA, RTA, RDTA — what do the letters mean?

R = rebuildable (you make the coil). D = dripping (no tank; juice goes straight on the cotton). T = tank (a glass reservoir). RDTA = a dripper deck sitting on top of a tank. “Sub-ohm tank” just means a tank with pre-made coils under 1 Ω.

I’ve never built a coil. Can I still run a rebuildable?

Yes — that’s what pre-built coils are for, and that’s why the first build is on us. Buy the atty, we coil and wick it at the counter and show you. Most people are doing their own within a week.

Which RDA is best for flavor?

Single-coil 22–24 mm drippers with a small chamber and bottom or low side airflow: Hadaly, Entheon, KRMA, Flave, GR1. Squonked, they’re hard to beat. Come taste one — we’ll build it for you.

What’s a bottom-feed (BF) pin?

A hollow 510 pin that lets a squonk mod push juice up into the RDA. Most of our RDAs include one; swap it in, screw the atty on a squonker, squeeze, vape.

Why does my tank taste burnt / leak?

Burnt: coil is dry (prime it, lower watts) or done (swap it). Leaking: cotton too thin, O-ring missing, or it sat on its side. Bring it in — it’s a two-minute fix and usually free.

Is it safe to build low on a mech?

Only if you know your battery’s continuous discharge rating and stay well under it. Use the Ohm’s-law bench above, build no lower than your cell allows, use authentic cells with clean wraps — and ask us. We’d rather check it than sell you a new hand.